Knowledge • Innovation • Support
ShaveMaster™The ShaveMaster™ from VIC International is a specially designed floor machine that makes a series of evenly spaced grooves to provide traction and reduce the risk of slips and falls.
The ShaveMaster™ uses diamond blades to create a precise pattern. Unlike scarifying or shot blasting, safety grooving leaves the floor structure intact and provides a long lasting, uniform appearance.
Watch the ShaveMaster Procedures & Maintenance video
Applications:
• Joint repair
• Prep surfaces
• Lippage removal
• Coatings removal
• Curled joint repair
• Aggregate exposure
• Improve floor flatness
• Paint striping removal
• Correct a poorly placed concrete slab
• Remove spalled areas or failing slurry caps
Benefits:
• Chemical free process
• Avoid lawsuits due to slip and fall claims
• Safety grooves don’t ‘"walk-off" like topical non-slip coatings
Technical Data
Weight 716 pounds
Motor output 15 hp
Power requirement 460 volt, three phase (40 amp circuit required)
Grinding width up to 13 inches
Discs diameter 10 inches
The number of diamond blades can be set up for grooving ramps, sidewalks, etc.
----------------------------------------
Increased Production--Saves Money
Production is typically 1,000 sq. ft. per hour of 1/8" concrete stock removal, using full 50 blade setup on normal concrete hardness.
Increases the removal rate from a typical 300 sq. ft. per hour (shot blasting or scarifying) to 1,000 sq. ft. per hour.
Description
Item #
ShaveMaster™
19942.RTG
Request a Quote
----------------------------------------------------------------------------------------------------------------------------------
Optima Multi Surface Floor Machines - 20"
The Multi Surface Machine is specifically designed to make small jobs highly profitable. Along with the rugged motor, it features a removable weight system. This system is manufactured in the USA.
• Extra heavy duty gears
• May be used wet or dry
• Complete with dust system for wet or dry usage
• Designed for the concrete industry, but can be used in other applications
• Six individual orbiting heads and 20" full velcro faced drive plate included (Orbital head system not recommended for other floor machines)
Motor Specs: 1 1/2 HP, 115V, 175 rpm
(230V available on special order)
Description
Item #
20" Multi Surface Machine
19903
Request a Quote
-----------------------------------------------------------------------------------------------------------------------------------------------------
The Husqvarna PG 820 is the largest in the range of surface preparation and finishing machines. Equipped with Dual Drive Technology™ the PG 820 is among the market’s most powerful and efficient machines. • A unique 5-way sealing mechanism protects bearings and internal parts from aggressive concrete dust and slurry, which contributes to a longer machinery service life before first service and between subsequent services. • Triple-headed grinder with features and a range of functions previously unavailable. • Dual Drive Technology™ – fully independent control of both planetary and satellite grinding heads in regards to speed and direction of rotation. • Extremely high production rates for rapid removal of tough heavy duty surfaces/coatings as well as floor polishing with an industrial and commercial capacity. Specifications for Husqvarna PG 820
Husqvarna PG 820
• Applications range from concrete floor preparation and repair to grinding and polishing of concrete floors as well as the repair and polishing of terrazzo and other natural stone.
Horse Power: 17HP
Weight of Machine: 970 lbs.
Grinding Diameter: 32"
Voltage: 3 phase/380-480 volts
| Description | Item # | |
| PG 820 | 33500 | Request a Quote |
-----------------------------------------------------------------------------------------------------------------------------------------------------
The Husqvarna PG 680 is an excellent choice for applications both large and small and especially commercial purposes. Smaller in size than the PG 820, the PG 680 is renowned for its maneuverability and ease of use without sacrificing power and output. • Applications range from concrete floor preparation and repair to grinding and polishing of concrete floors as well as the repair and polishing of terrazzo and other natural stone. • A unique 5-way sealing mechanism protects bearings and internal parts from aggressive concrete dust and slurry, which contributes to a longer machinery service life before first service and between subsequent services. • Triple-headed grinder with features and a range of functions previously unavailable. • Dual Drive Technology™ – fully independent control of both planetary and satellite grinding heads in regards to speed and direction of rotation. • Extremely high production rates for rapid removal of tough heavy duty surfaces/coatings as well as floor polishing with an industrial and commercial capacity.
Husqvarna PG 680
Specifications for Husqvarna PG 680
Horse Power: 17HP
Weight of Machine: 850 lbs.
Grinding Diameter: 27"
Voltage: 3 phase/380-480 volts
| Description | Item # | |
| PG 680 | 33502 | Request a Quote |
-----------------------------------------------------------------------------------------------------------------------------------------------------
The Husqvarna PG 530 is a planetary grinder available in both single and three phase versions with unmatched capacity, excellent for residential and light commercial purposes. The PG 530 combines the latest technology to deliver more power and performance than any other triple head planetary machine available in its class. • Applications range from concrete floor preparation and repair to grinding and polishing of concrete floors as well as the repair and polishing of terrazzo and other natural stone. • A unique 5-way sealing mechanism protects bearings and internal parts from aggressive concrete dust and slurry, which contributes to a longer machinery service life before first service and between subsequent services. • Triple-headed grinder with features and a range of functions previously unavailable. • High production rates for rapid removal of tough heavy-duty surfaces/coatings, as well as floor polishing with a light commercial and domestic capacity. • A flatter, more consistent grinding surface than that offered by other 4 headed machines. • Longer machinery service life thanks to the 5-way sealing mechanism, gear driven planetary head, premium quality belt, the spring steel head system and all zinc-plated steel parts. Specifications for Husqvarna PG 530
Husqvarna PG 530
Horse Power: 5HP
Weight of Machine: 475 lbs.
Grinding Diameter: 21"
Voltage: Single phase/220-240 volts or
Three phase/380-480 volts
| Description | Item # | |
| PG 530 - Single Phase | 33504 | Request a Quote |
| PG 530 - Three Phase | 33505 | Request a Quote |
-----------------------------------------------------------------------------------------------------------------------------------------------------
LAVINA 32® SPS
LAVINA 32® 20HP is a three-phase six-head planetary movement machine. Its design and construction frame are very comfortable for operation. We recommend LAVINA 32® 20HP for very large commercial jobs and for any commercial jobs that requires a very powerful grinding and surface preparation work.
• Thirty-two inch (32") wide grinding and polishing path with the tools touching the rim of the skirt and leaving only 5mm distance to the edge eliminates the need for additional edge work.
• Several lines of very aggressive diamond tools for various floor types were custom developed for LAVINA machines.
• One year warranty on parts and workmanship.
A user friendly design includes: Specifications for LAVINA 32® SPS
• Hourly meter that keeps track of the hours worked.
• Self-leveling skirt that keeps dust/dirt confined under the bowl.
• Soft Start technology allowing for a smooth start and a progressive power built-up.
• Pneumatic tires with pressure that can be adjusted according to the tools’ size.
• 2 Night vision lights which enables operator to direct the light as needed.
• Adjustable handle bars with 6 different positions intended for comfort and easy edge work.
• Vacuum port for dry applications.
• Variable speed motor bolted on top for convenient and fast inspection or repair
Horse Power: 20HP
Weight of Machine: 800 lbs.
Grinding Pressure: 551 lbs.
Voltage: 3 phase/230 volts
Amperage: 60 amp
Machine dimensions: 84.6" L x 35.4" W x 49.2" H
Description
Item #
Lavina 32® SPS
33204
Request a Quote
-----------------------------------------------------------------------------------------------------------------------------------------------------
LAVINA 25® SPS
LAVINA 25® planetary movement machine is best suited for average and large commercial jobs.
• Three and one phase capability. Easy conversion of phases. Excellent buy for the money.
• A twenty-five inch (25") wide grinding and polishing path with tools touching the rim of the skirt and leaving only 5mm distance to the edge eliminates the need for additional edge work.
• Designed for both dry and wet applications. When used dry, LAVINA 25® connects to DC3800c Twin vacuums by Dustcontrol or other conventional vacuums.
A user friendly design includes: Specifications for LAVINA 25® SPS
• Hourly meter that keeps track of the hours worked
• Self-leveling skirt that keeps dust/dirt confined under the bowl
• One-sided serpentine belt
• Soft Start technology allowing for a smooth start and a progressive power built-up
• Night vision light which enables operator to direct the light as needed
• Stackable weights with rubber bushings
• Adjustable handle bars with 6 different positions intended for comfort and easy edge work
• Vacuum port for dry applications
• Variable speed motor bolted on top for convenient and fast inspection or repair.
Horse Power: 7.5HP
Weight of Machine: 360 lbs.
Grinding Pressure: 220 lbs.
Voltage: single phase/230 volts
Amperage: 21.1 amp
Machine dimensions: 54" L x 27.6" W x 44" H
Description
Item #
Lavina 25® SPS
33201
Request a Quote
-----------------------------------------------------------------------------------------------------------------------------------------------------
LAVINA 20N Pro
Part of the revamped Lavina SPS system, the new floor machines Lavina Pro feature more horsepower, improved operation system and new color to match the new level of performance and productivity.
LAVINA 20®N Pro three-head planetary movement machine is best suited for residential and small commercial jobs.
A user friendly design includes: Specifications for LAVINA 20N Pro
• Solid handle for better control during manual transportation of the
machine
• Modular construction for easy transport and service. LAVINA
machines may be disassembled into easy-to-lift sections
• Each model features a built-in halogen headlight for work in darker
areas
• LAVINA machines feature several handles for easy transport and
maneuverability. The main handle (left) features 6 positions for
even greater control.
Griding Width: 20"
Weight: 334 lbs.
Power Requirements: 240 volts / Single Phase / 30 amp
Motor: 7.5 HP
Grinding Heads: 3
Head Pressure: 216 lbs.
Additional Weights: 2 x 48 lbs.
RPM: 300-1100 Variable Speed
Description
Item #
Lavina 20N Pro
33205
Request a Quote
Stonekor G&P OneThe G&P One is all about productivity. It is a solid Grinder and Polisher. No need for two machines on site, just one G&P One. A hefty, 1,300 lbs of concrete grinding muscle, taking concrete surface prep, grinding and polishing to new levels.
No back charges on jobs for utility bills. No need to pay for an onsite generator to power your equipment. Propane fuels the 22 hp Robin engine that is certified to meet EPA and CARB requirements with an Emissions Shut Down System and clean burning catalytic muffler. With a 30" cordless path, it utilizes three 13" rotating heads. Instead of multiple diamond changes, only three pre-loaded quick change plates are needed for each grit.
Wet grinding features include an 11 gallon water tank. Dry polishing features include a rear vacuum port located near the floor for more effcient dust collection. The frame of the machine routes the vacuum hose out to one side to keep the hose clear from machine operator.
Mechanical features include a Heavy Duty Kill Switch, Centrifugal Clutch, Vernier Throttle, and KOR™ Gearbox.
The G&P One comes standard with a Tach O Meter that displays engine hours, engine RPM and Service Intervals. Aluminum safety fuel cylinder with overfill prevention device (OPD) UL and DOT approved and Two Year limited warranty.
• Increased productivity
• Superior construction
• Simple design
• Ease of maintenance
• Dry vac port
• Water tank
• Quick change diamonds
• KOR™ gearbox
• EPA & CARB approved
Production
800-1,300 sq. ft. hour
Engine
Robin 22 hp (653 cc)
Engine Speed
3,200 rpm
Drum Speed
1,410 rpm
Head Speed
840 rpm
Grinding Pressure
785 rpm
Grinding Diameter
30"
Box Dimensions
80" L x 38" W x 55" H
Shipping Weight
1,385 lbs.
Description
Item #
G&P One
300134
Request a Quote
All STONEKOR burnishers EPA and CARB certified for exhaust emissions.
Stonekor Signature Series Burnishers
The Signature Series provides a variety of buffing widths in a high powered propane machine. No need for high voltage electric cords and generators. Run time is 5 to 6 hours per propane cylinder. Engine choices include
Leading the industry in concern for the environment and the safety of its operators; STONEKOR brings a new standard to each machine. All STONEKOR machines come standard with Emissions Shut Down System and Kill Switch. Optional Electric Clutch is available.
All machines come standard with service alert (hour) meter, 360 degree floating swivel spin-on pad driver, adjustable handle, aluminum safety fill fuel cylinder with overfill prevention device (OPD) UL and DOT approved and two year warranty.
• Endless run time
• Adjustable wheel brackets
• Adjustable handle
• Increased productivity
• Ergonomic design
• EPA & CARB approved
2100
2400
2700
Production
25,000 sq. ft.
28,000 sq. ft.
33,000 sq. ft.
Engine Speed
3,450 rpm
3,450 rpm
3,450 rpm
Pad Speed
2,000 rpm
1,800 rpm
1,800 rpm
Pad Size
21"
24"
27"
Box Dimensions
80" L x 38" W x 55" H
80" L x 38" W x 55" H
80" L x 38" W x 55" H
Shipping Weight
270 lbs.
330 lbs.
350 lbs.
Description
Item #
21" - Kawasaki 17 hp
300121
Request a Quote
24" - Kawasaki 17 hp
300122
Request a Quote
27" - Kawasaki 17 hp
300123
Request a Quote
27" - Robin 22 hp
300120
Request a Quote
All STONEKOR burnishers EPA and CARB certified for exhaust emissions.
Stonekor Dust Control Series Burnishers
The Dust Control Series provides a variety of buffing widths in a high powered propane machine. Available with your choice of
Leading the industry in concern for the environment and the safety of its operators; STONEKOR brings a new standard to each machine. All STONEKOR machines come standard with Emissions Shut Down System and Kill Switch. Optional Electric Clutch is available.
All machines come standard with service alert (hour) meter, 360 degree floating swivel spin-on pad driver, adjustable handle, aluminum safety fill fuel cylinder with overfill prevention device (OPD) UL and DOT approved and two year warranty.
• Reduce dust & improve air quality
• Ergonomic design
• Reusable dust filter bad
• Metal dust containment shroud
• Neoprene dust skirt
• Adjustable wheel brackets
• Heavy duty construction
• EPA & CARB approved
2400
2700
Production
28,000 sq. ft.
33,000 sq. ft.
Engine Speed
3,450 rpm
3,450 rpm
Pad Speed
1,800 rpm
1,800 rpm
Pad Size
24"
27"
Box Dimensions
52" L x 37.5" W x 46" H
52" L x 37.5" W x 46" H
Shipping Weight
330 lbs.
350 lbs.
Description
Item #
24" - Kawasaki 17 hp
300125
Request a Quote
27" - Kawasaki 17 hp
300126
Request a Quote
27" - Robin 22 hp
300119
Request a Quote
All STONEKOR burnishers EPA and CARB certified for exhaust emissions.
Stonekor EnviroPro Series Burnishers
The EnviroPro Series increases floor temperature during burnishing so that the gloss level rises with use of densifers. Built to meet GS-40 and LEED standards set for floor maintenance to capture dust and keep the working environment safe. This aluminum frame burnisher controls airborne debris with a unique air funnel system that traps and filters dust. Run time is 5 to 6 hours for one propane cylinder.
EnviroPro WB27, which while burnishing increases the floor temperature. The increase in Floor temperature increases the shine. This machine is great for concrete polishing with black or diamond pads. EnviroPro WB27 comes with a handheld infrared thermometer and a weighted metal pad driver.
Each machine comes standard with 360 degree floating swivel spin-on pad driver, Kill Switch, Emissions Shut Down system, adjustable handle, Tach O Meter, safety-fill fuel cylinder with overfill prevention device (OPD) UL and DOT approved, and limited two year warranty.
• Emissions shut down system
• Three-way catalytic muffler
• Built to meet GS-40 and LEED requirements
• Reusable dust bag
• Full contact weighted pad holder
• Produces heat required to set concrete sealers, guards, densifiers and impregnators
2100
2400
2700
Production
25,000 sq. ft.
28,000 sq. ft.
33,000 sq. ft.
Engine Speed
3,450 rpm
3,450 rpm
3,450 rpm
Pad Speed
2,000 rpm
1,800 rpm
1,800 rpm
Pad Size
21"
24"
27"
Box Dimensions
80" L x 38" W x 55" H
80" L x 38" W x 55" H
80" L x 38" W x 55" H
Shipping Weight
270 lbs.
330 lbs.
350 lbs.
Description
Item #
21" - Kawasaki 17 hp
300121
Request a Quote
24" - Kawasaki 17 hp
300122
Request a Quote
27" - Kawasaki 17 hp
300123
Request a Quote
27" - Robin 22 hp
300120
Request a Quote
All STONEKOR burnishers EPA and CARB certified for exhaust emissions.
Stonekor Tracker 3000
Tracker 3000 high production strip machine strips or scrubs in a 30” path with two 16” counter rotating brushes removing multiple layers of floor finish easily with its propane powered engine. No need for high voltage electric cords. Run time is 5 to 6 hours per propane cylinder. Available with your choice of
All machines come standard with service alert (hour) meter, two gear driven Strata Grit Plus 16” stripping brushes, easy change brush to pad drivers, transport wheel, adjustable handle, aluminum safety fill fuel cylinder with overfill prevention device (OPD) UL and DOT approved and two year warranty.
• Deep strip or scrub
• 30" cleaning path
• Two 16" gear driven brushes
• Low profile 4" deck
• Foam-filled tires
• Centrifugal clutch
• Gear box driven
• EPA & CARB approved
Production
20,000 sq. ft.
Engine Speed
3,450 rpm
Cleaning Width
30"
Brush Speed
320 rpm
Brush Size
Two 16" counter rotating brushes
Head Pressure
350 lbs.
Box Dimensions
52" L x 37.5" W x 46" H
Shipping Weight
1,385 lbs.
Description
Item #
Tracker 3000 - Kawasaki 17 hp
300124
Request a Quote
Tracker 3000 - Robin 22 hp
300117
Request a Quote
All STONEKOR burnishers EPA and CARB certified for exhaust emissions.
Stonekor Classic Propane Edger
The STONEKOR Classic Edger gives you a machine that will be the difference between being awarded a job and missing out due to unfinished edgework. The Classic Edger offers the ultimate in quick and efficient grinding, honing and polishing of the edges of any job, terrazzo or concrete, wet or dry. The adjustable three way head can grind to within 1/4" of walls and obstacles.
The STONEKOR propane system continues with The Classic Edger which is propane powered and requires no high voltage generator and no bulky, dangerous electrical cords.
The Classic Edger comes standard with a Tach O Meter that displays engine hours, engine RPM and service intervals. Leading the industry in concern for the environment and the safety of its operators, Stonekor brings a new standard on each machine. All Stonekor machines come with an Emissions Shut Down System and Kill Switch. Aluminum safety fuel cylinder with over fill prevention device (OPD) UL and DOT approved and Two Year limited warranty.
• Increased productivity
• Adjustable head pressure
• Rotating head
• Dry vac port
• Water tank
• No cords and no generators
• Centrifigual clutch
• EPA & CARB approved
Production
300-400 linear feet per hour
Engine
Kawasaki 17 hp
Engine Capability
3,200 rpm
Head RPM
640 rpm
Head Pressure
165 lbs. (factory head pressure)
Grinding Path
13"
Box Dimensions
52" L x 37.5" W x 56" H
Description
Item #
Classic grinder
300132
Request a Quote
All STONEKOR burnishers EPA and CARB certified for exhaust emissions.
VIC 3200 Grinder & Polisher
The VIC 3200 Floor machine for grinding and concrete polishing is highly productive and dependable reducing down time and increasing profitability. Here are some key features of our system:
• High productivity
• Low maintenance
• 775 lbs head pressure for flatter floors
• Easier to load, unload and maneuver on floor
• Unique tilting head for easier diamond changing
The VIC 3200 has hydraulic legs that lift the grinding head off the floor. This allows the head to be tilted back for easier and safer tool changes.
Griding Width: 32"
Weight: 930 lbs.
Power Requirements: 460 volts / 3 Phase / 30 amp
Motor: 15 HP
Grinding Heads: 3
Head Pressure: 775 lbs.
RPM: 350-1400 Variable Speed
Description
Item #
VIC 3200
33001.V
Request a Quote
VIC 2400 Grinder & Polisher
The VIC 2400 Prep and Polishing machine offers the greatest amount of down-head pressure available in the mid-range concrete polishing category.
This model combines strategic head plate and tool placements together with precise shroud design for minimizing distances to the wall.
For a mid-range machine, this VIC 24-inch model is a "beast" in the category for sheer power and balanced weight delivering an approximate 500-square-feet-per-hour production rate. With the increased down-head pressure for efficiency, this equates to increased productivity resulting in higher profitability for the contractor.
• Planetary head design
• Special design allow polishing close to walls
• Robust 230v, three-phase 10 horsepower, variable speed motor with reverse
• Positive drive system features a cog belt, a serpentine belt for drum rotation and tensioning, and a belt tensioner
Griding Width: 24"
Weight: 750 lbs.
Power Requirements: 230 volts / 3 Phase / 30 amp
Motor: 10 HP
Grinding Heads: 3
Head Pressure: 600 lbs.
RPM: 350-1400 Variable Speed
Description
Item #
VIC 2400
33002.C
Request a Quote
